Monkey Business - Red
A few years ago the ICON design crew sat around our favorite hookah theorizing about the impending Monkey versus Robot Armageddon. As the last of the bath salts charcoalized, it became clear that this would be no ordinary conflict. This “Primate V Automaton” battle would be a truly magnificent affair worthy of its own helmet graphic...and song. While you can now view (buy!) the Airmada Monkey Business graphic, you’ll have to visit us in person to hear the song. Bring your own salts.
Meets DOT FMVSS 218 (US), ECE 22-05 (Europe), SAI AS1698:2006 (Australia) & PSC (Japan) Helmet Safety Standards.
Fog-Free Icon Optics™ shield with Rapid-Release™ system and ProLock™ positive shield locking system. Also fits Icon Tracshield™ with tear-off posts.
Sublimated Hydradry™ moisture wicking liner.
Injection molded polycarbonate shell for strength and durability.
Let’s face it, Icon® helmets look cool and you want to keep them that way. We’ve found the following methods work really well to keep our helmets looking sharp and ready to roll. Remember, never use gas, pre-mix, carb cleaner, brake cleaner or any other random unlabeled spray can lying around the garage. Chemicals and harsh solvents can break down the materials in your helmet; it’s like using brake cleaner to polish your plastics—don’t do it!
1. Remove interior lining as shown on page 10 of the User Manual. 2. Soak your interior in a mild solution of baby shampoo. 3. Rinse in clean water several times until all soap is gone. 4. Let interior air dry and replace accordingly. * Never machine wash or dry your helmet interior.
Your helmet is equipped with a scratch resistant fog free shield. Common household cleaners such as glass cleaners, surface cleaners, and furniture cleaners, can leave behind unwanted residues, or in some extreme cases damage the shield itself. It is our recommendation the same steps outlined above for cleaning the exterior of your helmet should be applied to cleaning the exterior of your shield. Use no cleaners or detergents on the inside of your shield. Using anything other than a clean soft cloth, micro fiber cloth, or the bag supplied with your helmet, will ruin or reduce the effectiveness of the fog free coating.
It is a good idea to protect your helmet if it is stored for a period of time. Store your helmet inside the helmet bag we have provided in a secure, dry place out of direct exposure to sunlight.
Exterior Cleaning (Gloss Helmets)
1. Lay a warm, wet, cloth towel on the exterior of the helmet for at least 5 minutes to soften dried on bugs. (Don't skip this step!) 2. Using a fresh, wet, clean cloth and mild dish soap wipe down the exterior to get ride of road grime and softened bug guts. 3. Use another fresh dry cloth towel to dry the helmet and get rid of any water spots. * Never machine wash or dry your helmet interior.
Exterior Cleaning (Rubatone Helmets)
1. Lay a warm, wet, cloth towel on the exterior of the helmet for at least 5 minutes to soften dried on bugs. 2.Remove the now softened bugs and road grime with a light blotting action. For this use the soft part of your helmet bag provided or a clean microfiber cloth. * Never rub aggressively with anything on the Rubatone™ or you can ruin the finish.
1. For gloss helmet finishes, use spray automotive wax that is specifically designed for cars with a clear coat. (Available at any automotive store.) 2. For matte finishes, you know better than to polish a matte finish don’t you?
One Impact Rule - Any helmet that has sustained an impact should be replaced. Helmets are designed to absorb only one impact. The helmet is designed to absorb some shock by partial destruction of the shell and liner. After your helmet has endured any impact, the impact absorption liner portion of your helmet will have dispersed the energy from that impact, thus rendering the liner compacted and, therefore, compromised. This damage may not be visible. Even if there is no VISIBLE damage to the shell, the helmet’s usefulness is expired after one impact. A helmet that has experienced an impact should be destroyed and replaced, even if it is apparently undamaged. Obsolesence and Helmet Disposal - A helmet has a limited lifespan in use and should be replaced when it shows obvious signs of wear, e.g. change of fit, cracks, rust, fraying or other signs of normal “wear and tear” that can contribute to helmet degradation.
More Fun Than A Barrel of Monkeys
The Airmada fits extremely close to the head by virtue of its low profile shell. Additionally, the Airmada features a recessed twin-channel supervent with integrated spoiler to reduce helmet buffeting at high speeds.
Alliance GT Helmet
The Alliance GT’s has not one, but two shields. The quick-change fog-free Proshield keeps the bugs in check while the internal interchangeable drop shield stands on guard for sudden sun encounters. Just flip the switch, drop the shield, and dump the clutch.
The energy absorbing EPS foam liner uses our rider-preferred longer oval head form for a personalized fit without wasting an ounce of space. Combine that with superior venting, removable breath deflector, and a washable Hydradry moisture wicking interior creates a nearly perfect rider-focused enclosure. Once on you may never want to take it off.
Designed to fit Airframe Pro and Airmada Helmets
The IconOptics™ shield is fitted with a helmet shield lock to keep your shield securely closed. Sideplates (sold separately) mount to each side of the IconOptics shield for a more custom, finished look.
Compatible with the Airmada Helmet
The flat Icon TracShield™ is available for the Airmada as a factory solution for riders who require tear-offs. Compatible with our Rapid Release™ shield change mechanism, the TracShield™ can be used on the Airframe Pro and Airmada helmets, and is available in Dark Smoke, Clear, Yellow, and RST Silver. Tear-offs are available separately.
Complete The Look
Head to Toe, We've got you covered
We take the hit so you don't have to. Whether you're carving the canyon roads or headed for a night out, we've got the gear to keep you covered and looking fly.